Now shipping to 40+ countries · CE & ISO-certified, factory-direct Get a quote in 24h →

Bathroom pod flood-tested before it ships

A bathroom or kitchen pod arrives as a finished room with tiling, sanitaryware and drainage in place, and is craned through a prepared opening so a wet trade never enters the building.

Why this home
  • Factory testing catches a leak before the room is surrounded by finished walls.
  • A tray moulded into the pod, so the only site joint is the line at the door.
  • Tiling, sanitaryware and joinery fitted and tested before the pod leaves the factory.
  • Services leave on one face, which lands against the riser and keeps the corridor clear.
  • Valves and traps behind a panel inside the pod, reachable without opening a wall.

Choose a configuration

From $8,000 / set Factory-direct indicative price · exact quote after consultation
Factory-direct pricing Ships worldwide

A bathroom or kitchen pod arrives as a finished room with tiling, sanitaryware and drainage in place, and is craned through a prepared opening so a wet trade never enters the building.

A tray formed inside the pod, not laid over it

The pod floor is moulded as one tray with falls to the gully and upstands at every wall, and the wall lining laps over the upstand so water cannot get behind it. Because the tray is part of the pod, the only waterproof joint left on site is the line where the pod edge meets the building floor.

A wet room planned to the millimetre

Door swing, shower screen and basin are set out so a person can turn inside without touching the walls, and the WC sits off the sight line from the door. Kitchen pods follow the same discipline: sink, hob, fridge and worktop are fixed around the service wall, so the working triangle stays tight in a small room.

Drainage and fittings grouped at one service face

Waste, water and power leave the pod at a single face, which is the face that lands against the riser or the corridor wall. Isolating valves and traps sit behind a removable panel inside the pod, so a maintenance visit does not start with cutting a ceiling.

Extract sized to the room, ducted to the building

The bathroom extract grille sits above the shower, and the kitchen hood connection has its grease filter reachable from inside the room. The duct route is drawn with the pod so the spigot lands at the building shaft, not wherever it happens to fall on the pod.

Through the opening, before the facade closes

The pod is dimensioned to pass through a marked opening in the facade or at the slab edge, and it is lifted on a spreader beam so the tray does not carry the load. The opening is closed behind it, which is why the lift sequence is agreed with the main contractor before the first pod is built.

Set true, connected and tested before handover

The pod is packed and grouted at its bearing points so the tray falls the right way, then the services are connected at the single face and the extract is commissioned. A slow fill and a dye test at the trap confirm the joints before the room is handed over.

Bathroom pod flood-tested before it ships — Specifications
FinishesCustom colours
StyleContemporary
MaterialSteel
Best forOffices, Schools, Carports, Gardens

Included as standard

  • Structural steel module
  • Insulated wall and roof panels
  • Doors and windows
  • Electrical rough-in
  • Interior finish
  • Flooring

Typical lead time: production 4–8 weeks, freight 3–6 weeks depending on destination port.

How is the step at the pod door handled?

The pod sits on its own frame, so its finished floor level is set slightly above the structural slab and a transition strip or a small ramp closes the difference at the door. The height is fixed on the installation drawing and coordinated with the corridor finish, because a tile bed added later can leave the pod floor below the hallway. Where level access is needed, the pod is set into a recess in the slab rather than packed up.

How does a pod bathroom connect to the building drainage?

All waste leaves through a single stub at the service face, which is positioned against the riser or the wall where the stack runs. On site the stub is coupled to the building pipe with a flexible connector, and the fall is checked before the pod is finally packed and grouted. Because the pipework inside the pod is already complete, the connection is one joint rather than a run of new drainage under a finished floor.

If something fails, can a bathroom pod be serviced without opening a wall?

Service points are grouped so they are reachable from inside the pod: isolation valves, trap access and the electrical board sit behind panels that lift off, and no finished bedroom wall has to be opened. The single junction made on site, the joint between pod and floor, is detailed on the drawings so a leak stays inside the tray instead of travelling to the room below.

How is the waterproof tray of a bathroom pod made and proved?

The tray is formed inside the pod itself, with falls toward the gully and raised upstands at the wall junctions, and it is flooded before dispatch so the seal is proved while the waste is already in place. On site only one junction remains: the line between the pod edge and the building floor, made good exactly as the sealant detail on your drawings shows.

How do bathroom pod stacks line up from floor to floor?

Pods are set out from one common riser grid: the drawings fix each unit’s position against the shaft, and repeat floors use the same module rather than a fresh one each level. Setting-out tolerances, sleeve sizes and the discharge flange detail are coordinated with your services designer before production, because a stack that lands out of line becomes a site problem nobody wants.

How is a bathroom pod lifted into a building that is still under construction?

Through an opening designed for it: the facade panel or slab edge that comes out last is marked on the structural drawings, the pod travels at its shipping dimension and passes through, and the opening is rebuilt behind it. Lifting weight, the route and the crane position are agreed with your contractor before production, because a pod that will not fit cannot be cut down without losing the tray.

Are pods delivered fully finished?

Yes — each pod arrives with tiling, sanitaryware, joinery and fittings installed and factory-tested. On site you connect water, waste and electrical supplies to prepared points.

How fast can a bathroom pod be up and running?

Most units are placed on prepared footings and connected to power within a few days of delivery. Because the module arrives pre-fitted — walls, wiring, finish and flooring included — site work is limited to foundations and hook-ups. Count on 4–8 weeks of production plus 3–6 weeks of freight to your port, so order with your move-in date in mind.

Tell us your project.
We'll quote in 24 hours.

Tell us your site, timeline and configuration and we'll return a feasibility note, indicative budget and one to three recommended models.

Reply within one business day NDA on request English · German · French · Spanish

Request a quote — Bathroom pod flood-tested before it ships