Sandwich panel for wall and ceiling cladding
An insulated panel supplied as a wall in one piece: two facings bonded to a core, cut to your lengths, with a tongue-and-groove joint and the fixings hidden in the groove so the face runs unbroken.
- Bundles banded on dunnage and lifted with a clamp, so the face arrives without a crease.
- Cores chosen per job: light foam for a partition, mineral fibre where the build-up must not add fuel.
- Stored and installed on edge, which keeps a long panel straight until it is fixed.
- The same joint detail works on a wall, a ceiling and a container conversion.
- Facings bonded to a core, so the panel arrives as a wall rather than a frame to fill on site.
Choose a configuration
An insulated panel supplied as a wall in one piece: two facings bonded to a core, cut to your lengths, with a tongue-and-groove joint and the fixings hidden in the groove so the face runs unbroken.
A sandwich, so the core decides the wall
The panel is two facings bonded to a core, and that core is what the wall will actually be: rigid foam for light weight, mineral fibre where the build-up must not feed a fire. The facings carry the finish and take the fixings, so their gauge and coating decide how the panel behaves under a knock, a washdown and a scratch.
Thickness buys comfort, the core sets the rest
Thermal performance follows the core thickness and its conductivity, so a thicker panel holds a room with less heating and cooling, at the cost of weight on the frame behind it. Fire behaviour is a property of the core as well: mineral fibre is chosen where the assembly must not add fuel, and the panel data sheet is the document a building officer will read.
Module width, length cut to the wall
Panels are made to a module width and cut to the length of your wall, so the horizontal joints are few and every vertical joint lands on the frame instead of in mid-air. A longer panel spans further between rails, which matters on a roof where the purlin spacing sets the cost of the steel behind it.
The tongue-and-groove joint does the sealing
The joint is a tongue into a groove with a gasket squeezed between them, and the screw sits hidden in that groove rather than driven through the face, so water runs down the panel and off the lap instead of into a fixing head. Cut edges, corners and the base are closed with trims and a sealant matched to the facing, because an open core edge is where a panel fails first.
Bundles, clamps and the film that comes off
Panels travel in bundles on dunnage, banded and wrapped, with the protective film still on the face and the trims crated separately. They are lifted with a clamp or a spreader rather than by the edge, and on site they stand on edge, because a bundle left flat in the sun bows before anyone fixes it.
Same panel, different jobs
One panel line closes a cold store, documents a container conversion, separates a kitchen from a yard and finishes the ceiling over a washdown bay. What changes between those jobs is the core, the thickness and the joint detail, and those are settled per application rather than picked off a shelf. Typical uses include family homes and garage conversions.
| Style | Modern |
|---|
Included as standard
- Panels cut to length
- Fixing screws
- Starting and corner trims
- Installation guide
- Finish sample card
- Protective packaging
Typical lead time: production 2–5 weeks, freight 3–6 weeks depending on destination port.
How is a sandwich panel packed for transport?
Panels travel in bundles on protective blocks, banded and wrapped, with trims and fixings in separate crates. Bundles are marked by wall or roof zone so the crew unloads in the order of installation.
Which way round does a sandwich panel go on a wall?
With the tongue facing up and the groove down, so water running down the face reaches a lap that sheds it instead of a joint that opens into it. The wider spacing of the ribs, where there is one, goes to the outside, and the panel is laid from the sheltered corner towards the weather side. Setting the direction before the first panel is fixed saves redoing a whole elevation.
Is this the same as SIP panels?
No — structural insulated panels (SIP panels) are thick OSB-faced blocks that carry floor and roof loads. These are cladding panels: whatever the thickness, they fix to battens or a substructure and the load stays in the frame behind them.
Where can insulated sandwich panels be used?
As wall and ceiling cladding: interior feature walls, shop and office fit-outs, and lining on prefab or container buildings. The surface wipes clean, so kitchens, bathrooms and retail back-of-house are the classic applications.
How do you seal a panel that has been cut on site?
The cut is the weak point, because it exposes the core. A channel or a closing trim covers the edge, the core is kept dry and the joint is closed with a sealant that suits the facing rather than a general-purpose mastic. Where a panel is cut around an opening, the same trim goes around the reveal and the fixing pattern is kept back from the cut line.
Does a cold-store panel need a vapour barrier?
It needs the vapour on the warm side of the insulation, held out of the core, or moisture will condense inside the panel where nobody can see it. Joints are taped or sealed as a continuous layer, and penetrations for pipes and cables are sealed rather than left as a hole with a cable through it. Where the panel is used as a ceiling, the barrier goes above the lining and below the cold space.
How far can a panel span without support?
That depends on the load, the thickness and the acceptable deflection, not on the panel width alone, so it comes from the span table for the core you have chosen. On a roof the purlin spacing is set by that table, with snow and maintenance loads included rather than the panel's own weight only. Ask for the table with the quotation and give it to whoever designs the frame.
Can the panels be fixed over an existing wall?
Yes, on a batten or rail system that gives a straight plane and a ventilated cavity, because fixing straight onto an uneven wall telegraphs every hollow through the panel face. The cavity also lets the wall dry towards the outside, which matters on an old solid wall. The fixings then have to reach the structure behind, so their length is set by what the wall is made of.
Tell us your project.
We'll quote in 24 hours.
Tell us your site, timeline and configuration and we'll return a feasibility note, indicative budget and one to three recommended models.