Tiny house on foundation for family homes and villa projects
A tiny house built to stay in one place: a panel kit on a fixed pad, with full-height walls, a staircase to the loft and services connected once instead of unplugged for the road.
- Fixed water, waste and power connections that stay connected for good.
- Glazing sized with the heating load rather than added as an afterthought.
- Craned over a fence and set down in a garden with no rear access.
- Walls that rise to full height, because nothing has to clear a bridge.
- A staircase with a handrail instead of a ladder hooked to the wall.
Choose a configuration
A tiny house built to stay in one place: a panel kit on a fixed pad, with full-height walls, a staircase to the loft and services connected once instead of unplugged for the road.
A frame that is never folded for the road
The frame is a welded steel portal, so the walls rise to full height and the loft floor spans between beams instead of sitting over a wheel arch. Posts land on base plates that are drilled and set out before delivery, which keeps the house square from the first lift.
Walls that hold heat in a small volume
Panels arrive with the insulation bonded to the structural core, so there is no cavity to fill on site and no cold strip at the corners. The glazed gable is the weakest part of a small envelope, which is why the glass is chosen together with the heating load rather than after it.
A staircase, a loft, and a plan that works
The loft is reached by a staircase with a handrail, and the space beneath it takes the bathroom or a wall of storage instead of being lost. Below, the kitchen runs along one side and leaves a clear route from the entrance to the glazing. The heated floor area is 14.8 m². In practice the house is used for family homes and villa projects.
Connected once and then left alone
Water, waste and power come in as fixed connections with proper falls and insulation, because nothing has to be disconnected for a journey. A small ventilation unit runs continuously, taking moisture out of the kitchen and the shower before it settles on cold surfaces.
Lifted over the fence and set on the pad
The kit travels as wall panels, roof cassettes and a floor frame, and reaches a rear garden on a crane rather than a lorry. Assembly follows the numbered set: base plates, floor, walls and roof, with the shell closed before the kitchen and bathroom go in.
The plot decides the plan
Orientation settles where the glazing goes, how much sun the loft receives and whether the door faces the street or the garden. The pad is set out with drainage falls and anchor positions marked, so the house is held down where the engineer drew the straps and not wherever one happens to reach.
| Floor area | 14.8 m² |
|---|
Included as standard
- Prefabricated structural frame
- Roof and wall panels
- Doors and glazing
- Insulation package
- Fastening system
- Numbered assembly drawings
Typical lead time: production 6–10 weeks, freight 3–6 weeks depending on destination port.
Can a tiny house on foundation still be moved later?
Not easily, and that is the trade you accept with this version: a move takes a crane, a transport arrangement and a new base rather than a hitch and a drive. Most buyers choose it precisely because the site is settled — a garden, a family plot, a yard they intend to keep. If a move becomes likely, say so at drawing stage, because there is a middle route that keeps lifting points in the floor frame and lets the skirting come away in panels.
How long does it take to assemble a tiny house on foundation?
Most kits are weathertight within a few weeks of delivery: the frame and panels arrive prefabricated and the assembly crew works from numbered drawings. Interior finishing time depends on the configuration you choose. Count on 6–10 weeks of production plus 3–6 weeks of freight to your port before the kit lands.
Does a tiny house on foundation still need vehicle registration or plates?
No — once the house rests on a permanent pad it is dealt with as a building, not a trailer: there is no registration, no plate, and no road lighting, braking or coupling to maintain. That is the quiet advantage of this version, because the plan no longer has to squeeze inside transport limits, so a proper head height, wider rooms and a fixed staircase all become possible. Vehicle paperwork is replaced by local planning rules, which your authority confirms; we supply the dimension drawing and the specification sheet your application needs.
How does a crane reach a garden with no rear access?
Access is planned as a lift, not a delivery: the crane stands on the street or in a driveway and carries the load over the house or the fence on a fly jib. Overhead lines, tree cover and the weight of the largest panel set the crane size, and a street position may need a permit from the local authority. Send photographs and a sketch of the route, and the lift plan is drawn before the kit is booked.
Can the kit be assembled by an owner-builder?
The panels are numbered and pre-drilled, so a competent owner can close the shell with a helper and a hired crane, working from the drawings. Electrical, plumbing and drainage still need licensed trades, and those connections are inspected before the linings close. The slow part is not the frame but the setting out, so allow time for the base and for the lift plan.
How do you keep a small house with a loft free of condensation?
Moisture comes from cooking, showering and drying clothes, and a small volume saturates quickly, so continuous ventilation matters more than a bigger heater. The vapour control layer has to stay continuous behind the lining, with taped joints around the loft hatch and any flue penetration. A humidity meter costs little and tells you whether the ventilation is doing its job.
What can be done on a sloping site?
The pad can step with the ground, with the high side cut in and the low side built up on retained fill, or the house can sit on longer piers cut to level. What matters is that the bearing points are designed together, so the floor frame is not spanning a void it was never drawn for. A survey before the pad is marked out saves a redesign later.
Can a wood stove be fitted, and how does the flue leave the roof?
A stove is possible when the flue position is fixed on the drawings, because the roof penetration, the clearance to combustible material and the air supply all have to be built in rather than added. The flue usually leaves close to the ridge, with a flashing and a storm collar detailed for the roof profile. The installer signs off the appliance and the chimney, and that paperwork is worth keeping with the house documents.
Related models
Tell us your project.
We'll quote in 24 hours.
Tell us your site, timeline and configuration and we'll return a feasibility note, indicative budget and one to three recommended models.