Two-story prefab home for family homes, villa projects and hotels
A two-story house buys floor area from the same plot, and the stair decides almost everything else: where the bedrooms sit, how the wet rooms stack and how the house is raised in sections.
- A braced stair core that keeps both levels square during assembly and after.
- Insulation carried past the joist ends, so the floor band does not become a cold bridge.
- Bathrooms stacked over the kitchen, on one drainage stack for the whole house.
- Bedrooms on the quiet side, with a landing for linen and the vacuum.
- Ground floor braced first, upper sections lifted and bolted before the roof.
Choose a configuration
A two-story house buys floor area from the same plot, and the stair decides almost everything else: where the bedrooms sit, how the wet rooms stack and how the house is raised in sections.
The stair core ties the two levels together
The stair is not fitted into a finished house; it is part of the frame, and its walls work as a braced core that keeps both levels square with each other. Upper-floor joists land on the wall heads and are tied back to that core, so the building resists racking before the partitions and the roof are in place.
The floor band is where heat escapes
The line between the two storeys is the hardest part of the envelope: the floor structure crosses the wall, the joists interrupt the insulation, and outside air reaches the wall head from both sides. That band is built as a closed detail, with the insulation running past the joist ends and the air barrier taped before the cladding goes on.
Stairs in the middle, bedrooms above
Putting the stair at the centre of the plan shortens the upstairs corridor and lets the bathrooms stack directly over the kitchen and utility. Bedrooms go on the quiet side, the landing takes the linen and the vacuum, and the double-height space over the entrance stays small enough that it does not cost a room. The sleeping rooms are 4 bedrooms, mostly on the upper level. It is built for family homes, villa projects and hotels.
One wet stack serving both floors
The bathroom, the shower room and the kitchen share a vertical drainage stack, which is why the upper layout follows the lower one rather than the other way round. The boiler sits close to that stack so hot water does not travel across the house, and the upper emitters come off a manifold on the same wall.
The upper floor goes on once the lower is tied
The ground floor is assembled and braced first, then the upper sections are lifted onto the wall heads and bolted down before the roof follows. Props and temporary ties stay in place until the roof structure is complete, because a two-story frame is stable in its finished state, not halfway through. Wall panels are 75–150 mm thick.
A small footprint with a long shadow
Building upwards keeps the garden, but the taller elevation throws a shadow that has to be checked against the neighbour's windows and against the terrace you plan to use in the evening. Wind speed rises with height, and the crane or scaffold position at the boundary often decides which side the sections are lifted from.
| Bedrooms | 4 bedrooms |
|---|---|
| Storeys | 2 |
| Panel thickness | 75–150 mm |
| Colors | Custom colours |
| Style | Modern |
Included as standard
- Prefabricated structural frame
- Roof and wall panels
- Doors and glazing
- Insulation package
- Fastening system
- Numbered assembly drawings
Typical lead time: production 6–10 weeks, freight 3–6 weeks depending on destination port.
How does furniture get upstairs in a two-story prefab house?
Through the stair, which is why its width, its turning point and the landing are drawn around a bed base and a wardrobe rather than around the handrail. A straight flight takes more corridor but moves furniture easily; a winder saves space and is the reason people end up hoisting a mattress over a balcony. Tell your advisor which rooms are upstairs before the stair is fixed, and the plan can include a removable balustrade or a window that opens wide enough for the awkward items.
Can a two-story prefab home be built on a tight or sloping site?
Usually yes, because the way the building is divided for delivery is chosen around your access, not fixed by the design: on a narrow approach the two levels come as panels and deck cassettes instead of large modules. A crane or telehandler still needs firm, level ground to stand on and room to swing, so send photographs and your site plan and your advisor proposes the split that fits.
Are the stairs part of a two-story prefab home, or added later?
They are drawn with it: the flight, its landing and the guarding are fixed on the drawings alongside the floor opening, and the stair arrives either assembled or as a packaged flight put in straight after the floor deck. A stair core shapes both levels and the run of services, so settle its position before production. Moving it afterwards means redrawing the layout of the storey.
Can the layout be customised?
Yes — window positions, glazing size, the number of bedrooms and the balcony deck are adjusted before production. The kit ships numbered and pre-drilled for the plan you confirm, so late changes are the expensive kind. Finalise the plan with our advisors, then the factory cuts.
What foundation does it need?
A concrete slab, strip footings or pier foundations are all suitable, depending on soil and local practice. We supply the connection details for each option, so your local builder can prepare the base while the kit is in production.
How long does it take to assemble a two-story prefab home?
Most kits are weathertight within a few weeks of delivery: the frame and panels arrive prefabricated and the assembly crew works from numbered drawings. Interior finishing time depends on the configuration you choose. Count on 6–10 weeks of production plus 3–6 weeks of freight to your port before the kit lands.
Is the room directly under the roof comfortable in warm weather?
That depends on the roof build-up, which is a specification decision: insulation depth, a ventilated cavity, rooflights and shading are chosen for how your plot sits in the sun. Tell your advisor which rooms lie under the roof and which way they face, and the ceiling assembly is drawn for that case instead of taken from a standard sheet.
What is built into the line where the two floors meet?
That junction is a designed detail, not a site fix: wall heads bear on the floor plate through connection plates and bolts, a compressed gasket closes the seam against draught and rain, and the linings cover it inside. It is also where sound travels most easily between levels, so the floor build-up and the sealing of service penetrations are drawn with it. Roof and façade reveals at the same line appear on the elevations.
Related models
Tell us your project.
We'll quote in 24 hours.
Tell us your site, timeline and configuration and we'll return a feasibility note, indicative budget and one to three recommended models.