Two-story prefab home kit with a galvanised steel frame
A two-story house buys floor area from the same plot, and the stair decides almost everything else: where the bedrooms sit, how the wet rooms stack and how the house is raised in sections.
- Ground floor braced first, upper sections lifted and bolted before the roof.
- A double-height entrance kept small enough to leave a room upstairs.
- The garden stays, because the floor area goes up instead of out.
- Crane and transport positions checked against the boundary before production.
- A braced stair core that keeps both levels square during assembly and after.
Choose a configuration
A two-story house buys floor area from the same plot, and the stair decides almost everything else: where the bedrooms sit, how the wet rooms stack and how the house is raised in sections.
The stair core ties the two levels together
The stair is not fitted into a finished house; it is part of the frame, and its walls work as a braced core that keeps both levels square with each other. Upper-floor joists land on the wall heads and are tied back to that core, so the building resists racking before the partitions and the roof are in place. The frame is galvanised steel, with the stair core braced as one of its elements.
The floor band is where heat escapes
The line between the two storeys is the hardest part of the envelope: the floor structure crosses the wall, the joists interrupt the insulation, and outside air reaches the wall head from both sides. That band is built as a closed detail, with the insulation running past the joist ends and the air barrier taped before the cladding goes on.
Stairs in the middle, bedrooms above
Putting the stair at the centre of the plan shortens the upstairs corridor and lets the bathrooms stack directly over the kitchen and utility. Bedrooms go on the quiet side, the landing takes the linen and the vacuum, and the double-height space over the entrance stays small enough that it does not cost a room. It is built for garage conversions and retail units.
One wet stack serving both floors
The bathroom, the shower room and the kitchen share a vertical drainage stack, which is why the upper layout follows the lower one rather than the other way round. The boiler sits close to that stack so hot water does not travel across the house, and the upper emitters come off a manifold on the same wall.
The upper floor goes on once the lower is tied
The ground floor is assembled and braced first, then the upper sections are lifted onto the wall heads and bolted down before the roof follows. Props and temporary ties stay in place until the roof structure is complete, because a two-story frame is stable in its finished state, not halfway through.
A small footprint with a long shadow
Building upwards keeps the garden, but the taller elevation throws a shadow that has to be checked against the neighbour's windows and against the terrace you plan to use in the evening. Wind speed rises with height, and the crane or scaffold position at the boundary often decides which side the sections are lifted from.
| Structure | galvanised steel |
|---|---|
| Storeys | 2 |
| Colors | Custom colours |
Included as standard
- Prefabricated structural frame
- Roof and wall panels
- Doors and glazing
- Insulation package
- Fastening system
- Numbered assembly drawings
Typical lead time: production 6–10 weeks, freight 3–6 weeks depending on destination port.
How does furniture get upstairs in a two-story prefab house?
Through the stair, which is why its width, its turning point and the landing are drawn around a bed base and a wardrobe rather than around the handrail. A straight flight takes more corridor but moves furniture easily; a winder saves space and is the reason people end up hoisting a mattress over a balcony. Tell your advisor which rooms are upstairs before the stair is fixed, and the plan can include a removable balustrade or a window that opens wide enough for the awkward items.
Can the ground floor include a bedroom and bathroom for guests or older parents?
It can, and it is one of the most requested changes: a room that works as a study now and a bedroom later, with a shower room close enough to be used without crossing the house. That room needs the same door widths and level access as the rest of the ground floor, and the bathroom has to sit near the drainage stack to keep the falls simple. Ask for it at planning stage, because the stack position is what makes it cheap or expensive.
How is sound kept from travelling between the two floors?
The floor structure carries the impact noise, so the detail that matters is what sits above it: a floating floor build-up in the upper rooms and a resilient ceiling below stop footsteps better than a thicker carpet. Ducts and the stairwell are the other paths, because sound follows air; sealing the openings around pipes and fitting a door at the bottom of the stair helps. Bedrooms placed over the kitchen rather than over the living room solve a good part of the problem by geometry.
Should a two-story house include space for a future lift?
If the house is meant to be lived in for decades, a cupboard-sized shaft next to the stair is worth drawing even if the lift is fitted later. It costs a small amount of floor area, it keeps the structural opening and the power supply in the right place, and it avoids a much more invasive change when stairs become difficult. The alternative is a stair wide enough for a stair lift, which is cheaper to install but limits the plan.
How is the upper floor heated and cooled?
Heat rises, so the upper floor usually needs less than the ground floor, but it also overheats more easily because the roof is close and the windows catch more sun. Zoned heating with its own thermostat, shading on the south-facing glazing and a ventilation path through the stairwell keep the two levels closer together. If the upper rooms are under the roof, the insulation and the ventilation of that roof build-up matter more than the size of the radiator.
Can the two floors be built in separate stages?
Yes, if the frame and the base are designed for the completed house from the start: the foundations, the wall heads and the stair core have to carry the upper level even if it arrives a year later. The lower level is then closed with a temporary roof and a sealed stair opening, and the upper sections are lifted when the budget allows. Doing it this way costs less than a later extension, but the first phase has to be weathertight on its own.
Are the stairs part of a two-story prefab home, or added later?
They are drawn with it: the flight, its landing and the guarding are fixed on the drawings alongside the floor opening, and the stair arrives either assembled or as a packaged flight put in straight after the floor deck. A stair core shapes both levels and the run of services, so settle its position before production. Moving it afterwards means redrawing the layout of the storey.
How is the upper storey supported while the house is being assembled?
The ground-level walls and the floor deck go first onto the prepared base, and the upper floor plates bolt into their wall heads. The props you see at that stage carry the deck only until the bracing panels and bolts are tightened, after which the frame works as one piece and the temporary supports come away. That sequence is written into the assembly guide rather than left to the crew’s judgement.
Related models
Tell us your project.
We'll quote in 24 hours.
Tell us your site, timeline and configuration and we'll return a feasibility note, indicative budget and one to three recommended models.