Wooden villa for villa projects
A timber villa supplied as a closed kit: frame, roof and facade are cut and marked at the factory, with the species and grade recorded on the drawings, then assembled on a base prepared while the order runs through production.
- Overhangs sized for driving rain, shading sized for the west glass.
- Interior faces that can stay as exposed timber or take a lining later.
- A plant cupboard sized for hot water and ventilation before the frame is cut.
- Structural timber graded and marked, so each member traces back to its class.
- A ventilated cavity behind the facade, so the wall dries in both directions.
Choose a configuration
A timber villa supplied as a closed kit: frame, roof and facade are cut and marked at the factory, with the species and grade recorded on the drawings, then assembled on a base prepared while the order runs through production.
A frame in graded timber, not site-cut studs
Posts, beams and roof members are cut from graded structural timber and marked to the drawings, so the frame goes together in a set order and each member can be traced back to its strength class. Where a room needs a wider opening, a glued laminated beam carries the load instead of a post dropped into the middle of the wall.
A wall that can dry in both directions
The build-up has a ventilated cavity behind the cladding, a wind barrier over the sheathing and a vapour check on the warm side, so moisture that gets into the wall has a way out again. Insulation fills the full depth of the stud zone rather than being compressed into it, which keeps rooms warm without thick internal linings.
One room under the pitch, bedrooms below it
Kitchen, dining table and sitting area share a single volume, with the roof structure left exposed or closed according to the interior you choose, and bedrooms tucked under the lower part of the slope. Window openings follow the view and the sun rather than repeating at regular intervals along the facade. It is built for villa projects.
Cables and pipes kept on the warm side
Wiring and plumbing run in the service zone inside the vapour check, so no cable sits in a cold cavity and no pipe is left where frost can reach it. A plant cupboard holds the hot water unit and the ventilation, and its position is fixed while the frame drawings are still open.
Bundles that follow the frame sequence
The timber travels as numbered bundles, one per drawing page, with the connectors, fixings and membrane for that stage packed beside the members they belong to. A bundle is opened when its wall goes up, which keeps the wood out of the rain and the site clear of loose material.
Drawn for rain, sun and prevailing wind
Roof overhang, entrance side and terrace position are set against the weather the plot actually gets: a deep overhang on the driving-rain side, shade over the west glass, and the door turned out of the prevailing wind. Those decisions sit on the site plan, so the house does not have to defend itself with sealant later.
| Material | Timber |
|---|---|
| Best for | Villas |
Included as standard
- Prefabricated structural frame
- Roof and wall panels
- Doors and glazing
- Insulation package
- Fastening system
- Numbered assembly drawings
Typical lead time: production 6–10 weeks, freight 3–6 weeks depending on destination port.
Is a timber villa noisy between floors?
A bare timber floor transmits impact sound, so the build-up matters: a resilient layer under the screed or board, mineral insulation in the joist zone and a separate ceiling on resilient hangers cut the drum effect. Stairs are the other weak point, and a closed string with a solid balustrade is quieter than an open tread. Say early if the upper floor will be let separately, because that raises the acoustic target.
How is the wall detailed where the timber meets the ground?
The frame stops on a plinth or a sole plate above the damp course, with a ventilated zone and a drip so splash water never reaches the end grain. That detail is drawn together with the base, which is why the foundation height is fixed before the kit is produced. Getting it right is the single most useful thing you can do for the life of a timber wall.
Can I leave the timber exposed inside, or do I need lining?
Both are possible and both are drawn in advance: exposed frame and roof structure need the services routed in surface zones or behind a service wall, while a lined interior hides wiring in a normal cavity. Exposed timber shows joints and fixing points, so the frame layout becomes a design decision rather than a hidden one. Decide before production, because the two routes need different frame depths and different window reveal details.
How does a timber house behave in a fire?
Heavy timber chars at a predictable rate and keeps its section behind the char, which is why structural members are sized with that allowance rather than protected by a coating alone. What matters in practice is compartmentation, the escape route and the surfaces near the stove or flue, all of which follow your local building rules. Your designer sets those details and the fire service or building control signs them off.
What happens to the facade finish over the years?
A coated facade fades and chalks under ultraviolet light, and the coating is renewed when water stops beading rather than on a fixed date. Untreated larch or heat-treated timber is left to weather to a grey, which suits some sites and not others. The ventilated cavity behind the boards is what keeps either route working, because the back of the cladding can dry after rain.
What is included in the quoted price?
The quotation covers the structural kit and the finishes in your drawing set, plus export packing and loading. Freight, duties and the local slab or foundation are separate lines, so the budget stays transparent from the first enquiry to delivery.
Which timber should I use for the frame, and which for the facade?
The frame is generally a softwood such as spruce or pine, graded for structure and dried to the moisture content of the destination climate. For the outside, larch, heat-treated softwood or a coated board hold up better than untreated spruce, and the choice is recorded on the drawings so the factory and your painter work from the same specification. Tell your advisor about salt air or long damp seasons, because that moves the specification more than the look does.
Will the timber facade warp or crack over time?
Kiln-drying and factory profiling are exactly what limit movement: boards are dried to the moisture content of the destination climate and fixed with fixings that allow seasonal movement. Small surface checks are normal in any timber and do not affect the structure.
Related models
Tell us your project.
We'll quote in 24 hours.
Tell us your site, timeline and configuration and we'll return a feasibility note, indicative budget and one to three recommended models.